GD&T symbols reference: the fourteen characteristics explained

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Geometric dimensioning and tolerancing, GD&T, uses a small set of symbols in a framed box to control the shape, orientation and location of features. There are fourteen characteristics in five groups: form, profile, orientation, location and runout. Each page here explains one symbol in our own words, with how it is inspected and how to enter it in a report.
Detail A · The groups

Five groups, fourteen symbols

  • Form controls the shape of a feature on its own, with no datum: straightness, flatness, circularity and cylindricity.
  • Profile controls a line or surface against its true shape, with or without datums: profile of a line and profile of a surface.
  • Orientation controls tilt relative to a datum: angularity, perpendicularity and parallelism.
  • Location controls where a feature is: position, concentricity and symmetry.
  • Runout controls how much a surface wobbles as the part turns about a datum axis: circular runout and total runout.
Detail B · The frame

How to read a feature control frame

A frame is a row of boxes. From left to right: the characteristic symbol, the tolerance value (with a diameter sign if the zone is a cylinder, and an optional material modifier), then up to three datum letters in order of priority. The datum order matters, because it is the order in which the part is located before the measurement is taken.

In the tool, press GD&T on a row, choose the symbol and fill in the box. The tool writes the frame as text into the Requirement column and the report prints it. Frames are transcribed from the drawing; the tool does not interpret them or check that a frame is sensible.

The chart

Symbol (page) Group Needs a datum? What it controls
Straightness Form No How straight a line or axis is
Flatness Form No How flat a surface is
Circularity Form No How round a cross-section is
Cylindricity Form No How cylindrical a surface is, including taper and bow
Profile of a line Profile Sometimes A line on the part against its true shape
Profile of a surface Profile Sometimes A whole surface against its true shape
Angularity Orientation Yes Tilt at an angle other than 90 degrees
Perpendicularity Orientation Yes Tilt away from 90 degrees
Parallelism Orientation Yes How parallel a feature is to a datum
Position Location Usually Where a feature sits against its exact place
Concentricity Location Yes Offset of a derived axis from a datum axis
Symmetry Location Yes Offset of a derived median plane from a datum plane
Circular runout Runout Yes Wobble at one position as the part turns
Total runout Runout Yes Wobble over the whole surface as the part turns

How to enter each in a report

In the tool the GD&T builder writes the frame text into the Requirement column: the symbol, the tolerance, any modifier and the datum letters. Each characteristic page shows the exact text the tool writes for it.

Other symbols you will meet

The diameter sign in front of a tolerance means a cylindrical zone. The circled M and L are the material condition modifiers. A box around a number marks a basic dimension. Datum letters are explained on the datums page, and how to read a frame covers the reading order.

All fourteen

Mistakes that apply to every symbol

  • Reading the tolerance as a plus or minus. A GD&T tolerance is the total width of a zone.
  • Measuring from the wrong datum, or in the wrong order.
  • Treating a frame as a size tolerance. Size has its own limits on the same feature.
Does the tool check GD&T frames?
No. It writes the frame you transcribe into the report as text. It validates that the frame is well formed, for example that a form tolerance has no datum, but does not judge whether the frame suits the part.
Are these symbols from a standard?
The symbols on these pages are our own simplified drawings and the explanations are our own words. The standards that define GD&T are sold by their publishers, and nothing here reproduces them.
What is geometric tolerance?
A geometric tolerance controls the shape, orientation, location or runout of a feature, using a framed symbol, rather than its size alone. There are fourteen characteristics in five groups.
What does FOS mean in GD&T?
FOS stands for feature of size: a feature with a size, such as a hole or a pin, that can carry a material condition modifier. Planes and surfaces without a size are not features of size.
How do I read a GD&T symbols chart?
Find the symbol's group, check whether it needs a datum and read what it controls. The chart on this page links each symbol to its own page.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds