Straightness in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Straightness limits how far a line on a surface, or an axis, may bend away from a perfectly straight line.

Detail A · What it controls

What Straightness controls

Straightness is a form control. It asks how straight a single line is: either a line element running along a surface, or, when the frame carries a diameter sign, the axis of a feature such as a shaft. It says nothing about size on its own, and it has no datum, because a line is only compared with itself.

Tolerance zone. For a surface line the tolerance zone is the space between two parallel lines a tolerance value apart, in the plane of the view where the callout is shown. For an axis with a diameter sign the zone is a cylinder of that diameter around the true axis.

Detail B · How an inspector checks it

How Straightness is inspected

On a bench the usual method is a straightedge or a dial indicator that travels along the line while the part sits on a surface plate: the indicator range along the line is the straightness error. For an axis, a coordinate measuring machine takes points along the feature and fits a line to them. Remember that straightness is checked in the direction the callout is drawn, so inspect each line you are told to.

How to measure Straightness

Straightness is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
Dial indicator or straightedge Part on a surface plate, indicator travels along the line Indicator range along the line
CMM Points taken along the line or axis, a line is fitted Largest deviation from the fitted line

Straightness compared with Flatness

Commonly confused with The difference
Flatness Flatness limits a whole surface; straightness limits one line at a time.
Detail C · Entering it in the tool

How to enter Straightness in the tool

In the characteristic table, press GD&T on the row, choose the Straightness symbol, type the tolerance. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.05 is written as ⏤ | 0.05 on screen and as STR | 0.05 in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: No. It is a form tolerance, so the frame has only the symbol and the tolerance.

Worked example: reading and judging a Straightness frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ⏤ | 0.05. The tolerance is 0.05, which gives a zone 0.05 wide. The inspector measures the feature and finds a Straightness error of 0.040. That is less than 0.05, so the feature is in tolerance with room to spare. A second part measures 0.060. That is more than 0.05, so it is out of tolerance by 0.010. The report row for the second part carries the frame text as the requirement, 0.060 as the result, a verdict in words and a note saying what happened to the part.

Measured Straightness Tolerance Verdict
0.040 0.05 In tolerance
0.060 0.05 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Straightness

The common mistake is reading it as a limit on the whole surface. It limits individual lines only; a surface can have straight lines in one direction and still be warped across them, which is flatness. Another is checking size and forgetting that the size limit and the straightness limit are separate numbers on the same feature.

Does Straightness need a datum?
No. It is a form tolerance, so the frame has only the symbol and the tolerance.
Which group of controls is Straightness in?
It is a Form control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Straightness?
One common method is the Dial indicator or straightedge: Part on a surface plate, indicator travels along the line, and the inspector records: Indicator range along the line. The method table on this page lists the alternatives and what each records.
What is Straightness commonly confused with?
Flatness. Flatness limits a whole surface; straightness limits one line at a time.
How do I enter Straightness in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds