Feature control frame: how to read it, with three worked readings

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

A feature control frame is a rectangle divided into compartments that you read left to right: first the geometric characteristic symbol, then the tolerance zone with its diameter sign and any material condition modifier, then up to three datum references in order. It says: this feature must stay inside this zone, measured from these datums.
Detail A · Reading order

Left to right

  1. Symbol: which characteristic (position, flatness, perpendicularity and so on).
  2. Tolerance: the width of the zone. A diameter sign in front means a cylindrical zone.
  3. Modifier, if present: M (maximum material), L (least material).
  4. Datums: up to three letters, primary first, then secondary, then tertiary.
Detail B · Three readings

Worked examples

Frame Reading
Position, diameter 0.30, A, B The axis must lie within a 0.30 cylinder located from datums A then B
Flatness 0.05 The surface must lie between two parallel planes 0.05 apart. No datum needed
Perpendicularity 0.10, A The feature must lie between two planes 0.10 apart, perpendicular to datum A

Worked example: three frames with generated text

The tool writes frames as text. A position frame with a diameter zone prints as shown by the position page, and a flatness frame has no datum. Each of these is generated by the tool's own code, so what you read on the other characteristic pages matches what appears in your report. For the sample bushing, which carries no frames, the corresponding rows would hold only a size requirement; a frame would add a separate characteristic row.

How to enter one in a report

In the tool, open the GD&T builder, pick the symbol, enter the tolerance, modifier and datums, and the requirement column is filled with the frame text. See the symbol chart.

Common mistakes

  • Ignoring the order of datums.
  • Missing the diameter sign, which changes the zone shape.
  • Reading a basic dimension as if it had a plus-or-minus.

The pieces in more detail

The symbol compartment. The first compartment holds one of the fourteen geometric characteristic symbols. The symbol tells you which kind of control it is: form (flatness, straightness, circularity, cylindricity), orientation (parallelism, perpendicularity, angularity), location (position, concentricity, symmetry), runout, or profile.

The tolerance compartment. The number is the width of the tolerance zone. If a diameter sign sits in front, the zone is a cylinder or circle of that diameter. Without it, the zone is the space between two parallel lines or planes that far apart. This is a common reason for a wrong reading.

The datum compartments. Form controls have none. Others have one, two or three, from left to right in priority order.

Above and below the frame

Text above the frame, such as 4X, says how many features it covers. A note beneath, such as a datum feature symbol, links to the surface. A frame may also be attached to a dimension, which is a way of saying that it applies to the feature of size.

Why this matters for a report

The frame is the requirement. When you balloon it, copy the complete text into the Requirement column so a reader can see the symbol, zone and datums. Then record a single result: the measured value of the characteristic, compared with the tolerance.

How do you read a feature control frame?
Left to right: symbol, tolerance (with any modifier), then datums in order.
How do I enter a GD&T callout in an inspection report?
Use the GD&T builder, or write the frame as text in the Requirement column.
What are the parts of a feature control frame?
A symbol compartment, a tolerance compartment with an optional diameter sign and modifier, and up to three datum compartments in priority order.
What does the diameter sign in a frame mean?
It says the tolerance zone is a cylinder or circle of that diameter, not the space between two parallel lines or planes.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds