Cylindricity in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Cylindricity limits how far a whole cylindrical surface may depart from a perfect cylinder.

Detail A · What it controls

What Cylindricity controls

Cylindricity controls a complete cylindrical surface at once: roundness in every slice, straightness along the length, and taper, all together in one number. It is the strictest of the form controls for a cylinder and it has no datum.

Tolerance zone. The zone is the space between two coaxial cylinders a tolerance value apart. The surface must lie inside that annular volume over its full length.

Detail B · How an inspector checks it

How Cylindricity is inspected

A roundness tester with a vertical column probes several cross-sections and stitches them into a surface. A coordinate measuring machine with enough points along and around the feature can do the same. The result is a single radial spread, so plan the point count: a few rings of points will not reveal a slight taper or a barrel shape.

How to measure Cylindricity

Cylindricity is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
Roundness tester with column Trace several sections along the length Combined range across sections
CMM Points over the whole surface, a cylinder is fitted Radial spread about the fitted cylinder

Cylindricity compared with Circularity

Commonly confused with The difference
Circularity Cylindricity includes taper and bow along the length; circularity sees one section.
Detail C · Entering it in the tool

How to enter Cylindricity in the tool

In the characteristic table, press GD&T on the row, choose the Cylindricity symbol, type the tolerance. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.03 is written as ⌭ | 0.03 on screen and as CYL | 0.03 in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: No. Cylindricity is a form tolerance with no datum reference.

Worked example: reading and judging a Cylindricity frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ⌭ | 0.03. The tolerance is 0.03, which gives a zone 0.03 wide. The inspector measures the feature and finds a Cylindricity error of 0.024. That is less than 0.03, so the feature is in tolerance with room to spare. A second part measures 0.036. That is more than 0.03, so it is out of tolerance by 0.006. The report row for the second part carries the frame text as the requirement, 0.036 as the result, a verdict in words and a note saying what happened to the part.

Measured Cylindricity Tolerance Verdict
0.024 0.03 In tolerance
0.036 0.03 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Cylindricity

Asking for cylindricity when circularity and a straightness note would do, which costs measuring time for no functional gain. Or reading it as a size tolerance: the cylinder can be undersize or oversize and still meet cylindricity if its size limits are met separately.

Does Cylindricity need a datum?
No. Cylindricity is a form tolerance with no datum reference.
Which group of controls is Cylindricity in?
It is a Form control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Cylindricity?
One common method is the Roundness tester with column: Trace several sections along the length, and the inspector records: Combined range across sections. The method table on this page lists the alternatives and what each records.
What is Cylindricity commonly confused with?
Circularity. Cylindricity includes taper and bow along the length; circularity sees one section.
How do I enter Cylindricity in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds