Parallelism in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Parallelism limits how far a surface or axis may depart from being parallel to a datum.

Detail A · What it controls

What Parallelism controls

Parallelism controls how nearly a feature runs parallel to a datum. It is an orientation control. It limits tilt and also the flatness of a surface, so a bowed face can fail parallelism even when its two ends are level with the datum.

Tolerance zone. For a surface the zone is two parallel planes a tolerance value apart, parallel to the datum. For an axis with a diameter sign the zone is a cylinder parallel to the datum axis.

Detail B · How an inspector checks it

How Parallelism is inspected

Seat the datum feature on a surface plate and sweep an indicator over the controlled surface; the full indicator reading across the surface is the parallelism error. For two bores, a pin gauge in each with an indicator across them shows how far the axes depart. A coordinate measuring machine reports it directly after establishing the datum.

How to measure Parallelism

Parallelism is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
Dial indicator on a plate Datum face on the plate, indicator swept across the controlled surface Indicator range
CMM Datum plane built, points on the feature Zone width the feature occupies

Parallelism compared with Flatness

Commonly confused with The difference
Flatness Parallelism is measured from a datum; flatness is not.
Detail C · Entering it in the tool

How to enter Parallelism in the tool

In the characteristic table, press GD&T on the row, choose the Parallelism symbol, type the tolerance and choose the datum letters in the order the frame prints them. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.05 is written as ∥ | 0.05 | A on screen and as PARA | 0.05 | A in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: Yes. Parallelism is relative to a datum, so a datum reference is required.

Worked example: reading and judging a Parallelism frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ∥ | 0.05 | A. The tolerance is 0.05, which gives a zone 0.05 wide. The inspector measures the feature and finds a Parallelism error of 0.040. That is less than 0.05, so the feature is in tolerance with room to spare. A second part measures 0.060. That is more than 0.05, so it is out of tolerance by 0.010. The report row for the second part carries the frame text as the requirement, 0.060 as the result, a verdict in words and a note saying what happened to the part.

Measured Parallelism Tolerance Verdict
0.040 0.05 In tolerance
0.060 0.05 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Parallelism

Measuring thickness with a micrometer at a few points and calling it parallelism. A micrometer finds size variation between points, not the plane relationship. Also check that the datum is clean and seated; a chip under the datum surface shows up as a false parallelism error.

Does Parallelism need a datum?
Yes. Parallelism is relative to a datum, so a datum reference is required.
Which group of controls is Parallelism in?
It is a Orientation control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Parallelism?
One common method is the Dial indicator on a plate: Datum face on the plate, indicator swept across the controlled surface, and the inspector records: Indicator range. The method table on this page lists the alternatives and what each records.
What is Parallelism commonly confused with?
Flatness. Parallelism is measured from a datum; flatness is not.
How do I enter Parallelism in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds