How to read tolerances on an engineering drawing
Bilateral: nominal plus or minus a value
A length shown as 20.0 ±0.2 has a nominal of 20.0 and may be as small as 19.8 or as large as 20.2. Both limits come from the one number, which is why the tool fills both the upper and lower columns when it reads a plus-or-minus tolerance. The limits are worked out in exact decimals, so a result of exactly 20.2 is in tolerance.
Tolerance in only one direction
A diameter shown as Ø70.0 +0.03/0 may be larger than 70.0 by up to 0.03, but not smaller. Its limits are 70.0 and 70.03. Unilateral tolerances are common on fits, where the part must not go under a size. In the tool the upper tolerance is +0.03 and the lower is 0.
Both limits printed
Sometimes the drawing prints the two limits and no nominal, such as 12.05 over 11.95. The tool treats the middle value as the nominal and half the difference as the tolerance, so 12.05/11.95 becomes 12.000 with plus or minus 0.050. Nothing about the limits changes; only the way they are stored.
The title block fills the gaps
Many drawings leave most dimensions without a tolerance and say, in the title block, that general tolerances apply by number of decimal places: for example one value for dimensions with one decimal, a tighter one for two decimals, and an angular value for angles. A dimension with no tolerance of its own takes the general tolerance for its decimals, so 12.50 and 12.5 can have different limits.
In the tool, open Tolerances and parts, enter the values from the title block, and every dimension without its own tolerance uses them. A dimension that does carry a tolerance is not affected. The row shows the applied value as a hint, so you can see where a limit came from.
| No. | Requirement | Min | Max | Result | Verdict |
|---|---|---|---|---|---|
| 1 | 20.0 ±0.2 | 19.8 | 20.2 | 20.08 | IN TOL |
| 2 | 70.0 ±0.3 | 69.7 | 70.3 | 69.91 | IN TOL |
| 3 | ⌀110.0 ±0.1 | 109.9 | 110.1 | 110.04 | IN TOL |
| 4 | ⌀70.0 +0.03/0 | 70.0 | 70.03 | 70.02 | IN TOL |
| 5 | ⌀30.00 +0.02/0 | 30.00 | 30.02 | 30.01 | IN TOL |
| 6 | 4X ⌀9.0 ±0.1 THRU | 8.9 | 9.1 | 9.05 | IN TOL |
| 7 | ⌀90.0 ±0.1 B.C. | 89.9 | 90.1 | 90.03 | IN TOL |
Common mistakes
- Reading a unilateral tolerance as plus or minus.
- Applying a general tolerance to a dimension that has its own.
- Treating a reference dimension, shown in brackets, as if it had a tolerance. A reference dimension is information only.
- Comparing a result to a nominal and ignoring the limits.
For tolerances of form, orientation and location, see the GD&T reference.
Four kinds at a glance
| Kind | Printed as | Limits |
|---|---|---|
| Bilateral | 20.0 plus or minus 0.2 | 19.8 to 20.2 |
| Unilateral | 70.0 plus 0.03, minus 0 | 70.00 to 70.03 |
| Limit dimensions | 12.1 and 11.9 stacked | 11.9 to 12.1 |
| General | 36.50 with a title-block rule | From the rule; see the title-block guide |
What does out of tolerance mean?
The measured value lies outside the limits, even by the smallest amount: the part does not meet that requirement as drawn. What happens next depends on your system, usually a nonconformance record and a disposition.
Is a result exactly on the limit in tolerance?
Yes. A result exactly on a limit is in tolerance, and this tool compares in exact decimals, so 70.03 against an upper limit of 70.03 is in, not rounded either way. See ISO 2768 for general tolerance classes.
Worked example from the sample part
The sample shows three of the four kinds. Row 1, 20.0 plus or minus 0.2, is bilateral: 19.8 to 20.2. Row 4, diameter 70.0 plus 0.03 over zero, is unilateral: 70.00 to 70.03. Row 5, diameter 30.00 plus 0.02 over zero, is unilateral: 30.00 to 30.02. The same table shows the verdicts for the demonstration results.
| No. | Requirement | Min | Max | Result | Verdict |
|---|---|---|---|---|---|
| 1 | 20.0 ±0.2 | 19.8 | 20.2 | 20.08 | IN TOL |
| 2 | 70.0 ±0.3 | 69.7 | 70.3 | 69.91 | IN TOL |
| 3 | ⌀110.0 ±0.1 | 109.9 | 110.1 | 110.04 | IN TOL |
| 4 | ⌀70.0 +0.03/0 | 70.0 | 70.03 | 70.02 | IN TOL |
| 5 | ⌀30.00 +0.02/0 | 30.00 | 30.02 | 30.01 | IN TOL |
| 6 | 4X ⌀9.0 ±0.1 THRU | 8.9 | 9.1 | 9.05 | IN TOL |
| 7 | ⌀90.0 ±0.1 B.C. | 89.9 | 90.1 | 90.03 | IN TOL |
Row 5 is a good lesson in precision. It is printed to two decimals, so its limits and result are recorded to two decimals. Recording a result of 30.0 would hide whether it is above or below the limit of 30.02.
Tolerance in the units you were given
A tolerance on a metric drawing is in millimetres, and on an inch drawing in inches, unless the drawing says otherwise. Tolerances on angles are in degrees or degrees and minutes. Convert only when your instrument reports in another unit, and keep the unit on the report row so a reader can follow.
Fit tolerances in brief
Some drawings give limits as letter-number fits, such as H7 for a hole. The letters and number select a tolerance from a standard table by size. They are outside the scope of this page. If a drawing uses them, take the limits from the standard table and enter them as nominal with upper and lower tolerances.
Mistakes people make
- Reading a unilateral tolerance as bilateral. Plus 0.03 over zero is not plus or minus 0.03.
- Using a measuring tool that cannot resolve the tolerance.
- Taking the title-block tolerance when the dimension has its own.
- Rounding a result before comparing it.
- What if a dimension has no tolerance and the title block has none either?
- Then the drawing does not say what is acceptable, and you should ask the customer. The tool shows no verdict for such a row.
- Is an exact-limit result in or out?
- In. The tool uses exact decimal arithmetic, so a result exactly on a limit is in tolerance.
- What is the difference between bilateral and unilateral tolerance?
- A bilateral tolerance allows variation in both directions, such as 20.0 plus or minus 0.2, which gives 19.8 to 20.2. A unilateral tolerance allows it in one, such as 70.0 plus 0.03 over zero, which gives 70.00 to 70.03.
- What are limit dimensions?
- Limit dimensions print the upper and lower limits directly, for example 12.1 over 11.9, instead of a nominal and a tolerance. The part is in tolerance when the measured value lies between the two.
- What does tolerance mean in engineering?
- It is the permitted variation of a dimension from its nominal value. Parts are never made exactly to size, so the drawing says how far from nominal is still acceptable.
- Is a measurement exactly on the limit in tolerance?
- Yes. A result exactly on a limit is in tolerance, and this tool compares in exact decimals so it is never rounded to the wrong side.
Related
- How to balloon a drawing: a step-by-step method for inspection reports
- The Form 3-style inspection report, column by column
- GD&T symbols reference: the fourteen characteristics explained
- PPAP dimensional results explained, and how they differ from a first article report
- Open the tool and try it on a drawing