Symmetry in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Symmetry limits how far the median points of opposite surfaces may stray from a datum centre plane.

Detail A · What it controls

What Symmetry controls

Symmetry controls whether a feature, such as a slot or a key, is centred on a datum plane. It works from the median points between the opposite faces of the feature. Like concentricity it relies on those median points, so it takes more measurement than a simple size check.

Tolerance zone. The zone is the space between two parallel planes either side of the datum centre plane. The median surface of the feature must lie between them.

Detail B · How an inspector checks it

How Symmetry is inspected

Measure the width of the feature at many points and the position of each face from the datum plane, then compute the midpoint at each station. A coordinate measuring machine does this directly. A dial indicator on each face from a datum plane, with the part flipped, gives a slower manual answer.

How to measure Symmetry

Symmetry is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
CMM Median plane derived from opposite surfaces Offset of the median plane from the datum plane, doubled
Dial indicators on both sides Part flipped, readings compared Half the difference between sides

Symmetry compared with Position

Commonly confused with The difference
Position Symmetry uses derived median points; position of a feature of size measures the feature itself.
Detail C · Entering it in the tool

How to enter Symmetry in the tool

In the characteristic table, press GD&T on the row, choose the Symmetry symbol, type the tolerance and choose the datum letters in the order the frame prints them. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.1 is written as ⌯ | 0.1 | A on screen and as SYM | 0.1 | A in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: Yes. The datum is the centre plane the feature must be symmetric about.

Worked example: reading and judging a Symmetry frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ⌯ | 0.1 | A. The tolerance is 0.1, which gives a zone 0.1 wide. The inspector measures the feature and finds a Symmetry error of 0.08. That is less than 0.1, so the feature is in tolerance with room to spare. A second part measures 0.12. That is more than 0.1, so it is out of tolerance by 0.02. The report row for the second part carries the frame text as the requirement, 0.12 as the result, a verdict in words and a note saying what happened to the part.

Measured Symmetry Tolerance Verdict
0.08 0.1 In tolerance
0.12 0.1 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Symmetry

Treating it as a width tolerance. The slot can be the right width and off-centre, or the wrong width and centred. Another is using position of a slot as a substitute without saying so; the two zones are described differently and the report should name the control actually used.

Does Symmetry need a datum?
Yes. The datum is the centre plane the feature must be symmetric about.
Which group of controls is Symmetry in?
It is a Location control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Symmetry?
One common method is the CMM: Median plane derived from opposite surfaces, and the inspector records: Offset of the median plane from the datum plane, doubled. The method table on this page lists the alternatives and what each records.
What is Symmetry commonly confused with?
Position. Symmetry uses derived median points; position of a feature of size measures the feature itself.
How do I enter Symmetry in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds