Profile of a surface in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Profile of a surface limits a whole three-dimensional surface to a tolerance zone around its true shape.

Detail A · What it controls

What Profile of a surface controls

Profile of a surface controls every point on a surface against its true shape, taken from the drawing or the model. Depending on whether datums are listed it can control form alone, or form and orientation, or form and location, which makes it one of the most used frames on moulded and machined contours.

Tolerance zone. The zone is a thin shell, a tolerance value thick, around the true surface, normally split evenly either side. A note can make it unilateral or offset it.

Detail B · How an inspector checks it

How Profile of a surface is inspected

Scan or probe the surface with a coordinate measuring machine, or compare it with a gauge, and report the largest signed deviation from the true shape. Fix the part to the datums in the frame first, in the order listed, because the result depends on that alignment. A report as a colour map of deviations is common and easy to read.

How to measure Profile of a surface

Profile of a surface is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
CMM Points over the surface compared with the model or basic dimensions Largest deviation, reported against a band
Scanner Surface scanned and compared with the model Colour map and largest deviation

Profile of a surface compared with Profile of a line

Commonly confused with The difference
Profile of a line Surface profile covers the whole surface, not individual sections.
Detail C · Entering it in the tool

How to enter Profile of a surface in the tool

In the characteristic table, press GD&T on the row, choose the Profile of a surface symbol, type the tolerance and choose the datum letters in the order the frame prints them. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.5 is written as ⌓ | 0.5 | A | B on screen and as PROF-S | 0.5 | A | B in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: Often. Datum references decide whether location and orientation are controlled as well as form.

Worked example: reading and judging a Profile of a surface frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ⌓ | 0.5 | A | B. The tolerance is 0.5, which gives a zone 0.5 wide. The inspector measures the feature and finds a Profile of a surface error of 0.40. That is less than 0.5, so the feature is in tolerance with room to spare. A second part measures 0.60. That is more than 0.5, so it is out of tolerance by 0.10. The report row for the second part carries the frame text as the requirement, 0.60 as the result, a verdict in words and a note saying what happened to the part.

Measured Profile of a surface Tolerance Verdict
0.40 0.5 In tolerance
0.60 0.5 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Profile of a surface

Forgetting that the datums decide what is being controlled. The same number with and without datums is a different requirement. Also remember that an all-around or all-over symbol widens the area covered; read it before deciding which surfaces to measure.

Does Profile of a surface need a datum?
Often. Datum references decide whether location and orientation are controlled as well as form.
Which group of controls is Profile of a surface in?
It is a Profile control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Profile of a surface?
One common method is the CMM: Points over the surface compared with the model or basic dimensions, and the inspector records: Largest deviation, reported against a band. The method table on this page lists the alternatives and what each records.
What is Profile of a surface commonly confused with?
Profile of a line. Surface profile covers the whole surface, not individual sections.
How do I enter Profile of a surface in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds