Profile of a line in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Profile of a line limits a two-dimensional outline, checked in cross-sections, to a tolerance zone around its true shape.

Detail A · What it controls

What Profile of a line controls

Profile of a line controls the outline of a feature in each cross-section, such as the shape of a cam or an airfoil-like section, without controlling the surface between the sections. The true shape comes from the drawing or the model, and the actual outline must stay within a band around it.

Tolerance zone. The zone is a band, a tolerance value wide, following the true profile in each section plane. It may be bilateral, with half the band either side of the true profile, or shifted by a drawing note to be unilateral.

Detail B · How an inspector checks it

How Profile of a line is inspected

Take sections at the stations the drawing shows, using a profile projector or a coordinate measuring machine. Compare the measured outline with the true profile and read the largest departure. If datums are listed, locate the part from them first; if none are listed, the band may float to fit the outline, which is a form-only check.

How to measure Profile of a line

Profile of a line is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
Optical comparator Part on the stage, outline compared with an overlay Gap between outline and overlay
CMM Points taken along the line in the section the frame names Largest deviation from the true line, in a band

Profile of a line compared with Profile of a surface

Commonly confused with The difference
Profile of a surface A line profile is judged section by section; a surface profile is judged over the whole surface.
Detail C · Entering it in the tool

How to enter Profile of a line in the tool

In the characteristic table, press GD&T on the row, choose the Profile of a line symbol, type the tolerance and choose the datum letters in the order the frame prints them. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.2 is written as ⌒ | 0.2 | A on screen and as PROF-L | 0.2 | A in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: Optional. With datums the profile is also located and oriented; without them it controls shape only.

Worked example: reading and judging a Profile of a line frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ⌒ | 0.2 | A. The tolerance is 0.2, which gives a zone 0.2 wide. The inspector measures the feature and finds a Profile of a line error of 0.16. That is less than 0.2, so the feature is in tolerance with room to spare. A second part measures 0.24. That is more than 0.2, so it is out of tolerance by 0.04. The report row for the second part carries the frame text as the requirement, 0.24 as the result, a verdict in words and a note saying what happened to the part.

Measured Profile of a line Tolerance Verdict
0.16 0.2 In tolerance
0.24 0.2 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Profile of a line

Treating it like profile of a surface. A line profile says nothing about shape between the sections, so an unspecified section can be wrong and still pass. Another trap is forgetting whether the zone is bilateral or unilateral; read the note beside the frame before judging a result.

Does Profile of a line need a datum?
Optional. With datums the profile is also located and oriented; without them it controls shape only.
Which group of controls is Profile of a line in?
It is a Profile control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Profile of a line?
One common method is the Optical comparator: Part on the stage, outline compared with an overlay, and the inspector records: Gap between outline and overlay. The method table on this page lists the alternatives and what each records.
What is Profile of a line commonly confused with?
Profile of a surface. A line profile is judged section by section; a surface profile is judged over the whole surface.
How do I enter Profile of a line in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds