Position in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Position limits how far a feature's axis or centre plane may sit from its exact location, measured from the datums.

Detail A · What it controls

What Position controls

Position controls where a feature is. The true location comes from basic dimensions, shown boxed, measured from the datums in the order listed. The feature's axis or centre plane must stay inside a zone around that exact place. It is the usual way to locate holes, pins and slots.

Tolerance zone. For a hole axis the zone is normally a cylinder, shown by the diameter sign, centred on the true position. For a slot or tab it is the space between two parallel planes either side of the true centre plane.

Detail B · How an inspector checks it

How Position is inspected

A coordinate measuring machine aligns to the datums, finds the actual axis, and reports its distance from true position. The reported figure is a radial distance, so the zone diameter is twice that distance: compare twice the deviation with the tolerance. A functional gauge with fixed pins checks a pattern of holes in one go for production runs.

How to measure Position

Position is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
CMM Datums built, feature axis or centre measured Distance from true position, doubled, against the tolerance
Fixed gauge Part placed on the gauge, pins enter Pass or fail
Height gauge with pins Datums set up on the plate, coordinates read Coordinates, position calculated

Position compared with Concentricity

Commonly confused with The difference
Concentricity Position is the usual choice for locating a feature; concentricity is measured on derived median points.
Detail C · Entering it in the tool

How to enter Position in the tool

In the characteristic table, press GD&T on the row, choose the Position symbol, type the tolerance, tick Diameter zone, pick the material modifier shown on the drawing and choose the datum letters in the order the frame prints them. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.25 is written as ⌖ | Ø0.25 Ⓜ | A | B Ⓜ on screen and as POS | Ø0.25 (M) | A | B (M) in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: Yes, nearly always. The datums define the origin from which the basic dimensions are measured.

Worked example: reading and judging a Position frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ⌖ | Ø0.25 Ⓜ | A | B Ⓜ. The tolerance is 0.25, which gives a cylindrical zone 0.25 across. The inspector measures the feature and finds a Position error of 0.200. That is less than 0.25, so the feature is in tolerance with room to spare. A second part measures 0.300. That is more than 0.25, so it is out of tolerance by 0.050. The report row for the second part carries the frame text as the requirement, 0.300 as the result, a verdict in words and a note saying what happened to the part.

Measured Position Tolerance Verdict
0.200 0.25 In tolerance
0.300 0.25 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Position

Comparing the deviation directly with the tolerance when the tolerance is a diameter. If the frame carries a material modifier, extra tolerance becomes available as the hole departs from its limit size, so read the size of each hole before judging position. Another is measuring from the wrong datum order.

Does Position need a datum?
Yes, nearly always. The datums define the origin from which the basic dimensions are measured.
Which group of controls is Position in?
It is a Location control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Position?
One common method is the CMM: Datums built, feature axis or centre measured, and the inspector records: Distance from true position, doubled, against the tolerance. The method table on this page lists the alternatives and what each records.
What is Position commonly confused with?
Concentricity. Position is the usual choice for locating a feature; concentricity is measured on derived median points.
How do I enter Position in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds