Perpendicularity in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Perpendicularity limits how far a surface or axis may depart from a right angle to a datum.

Detail A · What it controls

What Perpendicularity controls

Perpendicularity controls the ninety-degree relationship between a feature and a datum. It is an orientation control: it fixes the tilt and also limits the form of a surface, but it does not control where along the datum the feature is placed.

Tolerance zone. For a face, the zone is two parallel planes a tolerance value apart, perpendicular to the datum. For a hole or pin axis with a diameter sign, the zone is a cylinder of that diameter standing perpendicular to the datum plane.

Detail B · How an inspector checks it

How Perpendicularity is inspected

Set the datum surface on a surface plate, then use a square and indicator, or an indicator on a height stand, to read the feature across its length; the spread is the error. For an axis, a coordinate measuring machine fits the axis and reports the cylinder it fits inside. A gauge pin in the hole against a plate is a quick functional check for a hole.

How to measure Perpendicularity

Perpendicularity is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
Square and indicator Datum on a plate, indicator across the surface or along the axis Indicator range
CMM Datum plane and the feature measured, deviation from 90 degrees derived Zone width the feature occupies

Perpendicularity compared with Angularity

Commonly confused with The difference
Angularity Perpendicularity is the 90 degree case; angularity covers other angles.
Detail C · Entering it in the tool

How to enter Perpendicularity in the tool

In the characteristic table, press GD&T on the row, choose the Perpendicularity symbol, type the tolerance, tick Diameter zone, pick the material modifier shown on the drawing and choose the datum letters in the order the frame prints them. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.05 is written as ⟂ | Ø0.05 Ⓜ | A on screen and as PERP | Ø0.05 (M) | A in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: Yes. The datum is the surface or axis the feature must stay square to.

Worked example: reading and judging a Perpendicularity frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ⟂ | Ø0.05 Ⓜ | A. The tolerance is 0.05, which gives a cylindrical zone 0.05 across. The inspector measures the feature and finds a Perpendicularity error of 0.040. That is less than 0.05, so the feature is in tolerance with room to spare. A second part measures 0.060. That is more than 0.05, so it is out of tolerance by 0.010. The report row for the second part carries the frame text as the requirement, 0.060 as the result, a verdict in words and a note saying what happened to the part.

Measured Perpendicularity Tolerance Verdict
0.040 0.05 In tolerance
0.060 0.05 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Perpendicularity

Using a try-square by eye on a tight tolerance, which hides small errors. Another is forgetting the modifier: a maximum material condition on the frame allows extra tolerance as the feature moves away from its maximum size, so the allowed error depends on the measured size.

Does Perpendicularity need a datum?
Yes. The datum is the surface or axis the feature must stay square to.
Which group of controls is Perpendicularity in?
It is a Orientation control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Perpendicularity?
One common method is the Square and indicator: Datum on a plate, indicator across the surface or along the axis, and the inspector records: Indicator range. The method table on this page lists the alternatives and what each records.
What is Perpendicularity commonly confused with?
Angularity. Perpendicularity is the 90 degree case; angularity covers other angles.
How do I enter Perpendicularity in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds