Circular runout in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Circular runout limits the variation a surface shows at each cross-section as the part turns about a datum axis.

Detail A · What it controls

What Circular runout controls

Circular runout controls a surface of revolution, or a face, against a datum axis while the part rotates. At each cross-section, the surface may move no more than the tolerance as indicated by a dial gauge. It combines roundness at that slice with how far the slice is off the axis.

Tolerance zone. The tolerance is the allowed total indicator movement at any one cross-section during one full turn. Each position along the surface is checked on its own.

Detail B · How an inspector checks it

How Circular runout is inspected

Mount the part on the datum, for example between centres or in a collet on the datum diameter, put a dial indicator against the surface, turn the part one full revolution and read the full indicator movement. Repeat at several positions along the surface. For a face, the indicator is placed on the face at a stated radius.

How to measure Circular runout

Circular runout is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
Dial indicator on centres or V-blocks Part turned a full turn, indicator on the surface Indicator range at each position
Runout tester Part on centres, indicator at set positions Greatest range

Circular runout compared with Total runout

Commonly confused with The difference
Total runout Circular runout is one position at a time; total runout traces the whole surface.
Detail C · Entering it in the tool

How to enter Circular runout in the tool

In the characteristic table, press GD&T on the row, choose the Circular runout symbol, type the tolerance and choose the datum letters in the order the frame prints them. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.05 is written as ↗ | 0.05 | A on screen and as RUN | 0.05 | A in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: Yes. Runout is always measured about a datum axis.

Worked example: reading and judging a Circular runout frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ↗ | 0.05 | A. The tolerance is 0.05, which gives a zone 0.05 wide. The inspector measures the feature and finds a Circular runout error of 0.040. That is less than 0.05, so the feature is in tolerance with room to spare. A second part measures 0.060. That is more than 0.05, so it is out of tolerance by 0.010. The report row for the second part carries the frame text as the requirement, 0.060 as the result, a verdict in words and a note saying what happened to the part.

Measured Circular runout Tolerance Verdict
0.040 0.05 In tolerance
0.060 0.05 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Circular runout

Mounting on the wrong feature. Runout is only meaningful from the datum axis, so a part clamped on a worn surface gives a number that mixes the clamping error with the part's. Also record the indicator reading as a total range, not half of it; the tolerance is on the full range.

Does Circular runout need a datum?
Yes. Runout is always measured about a datum axis.
Which group of controls is Circular runout in?
It is a Runout control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Circular runout?
One common method is the Dial indicator on centres or V-blocks: Part turned a full turn, indicator on the surface, and the inspector records: Indicator range at each position. The method table on this page lists the alternatives and what each records.
What is Circular runout commonly confused with?
Total runout. Circular runout is one position at a time; total runout traces the whole surface.
How do I enter Circular runout in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds