Circularity in GD&T

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Circularity limits how far each cross-section of a round feature may depart from a perfect circle.

Detail A · What it controls

What Circularity controls

Circularity, often called roundness, is a form control applied to a round feature. Take any slice perpendicular to the axis: the outline must sit between two concentric circles a tolerance value apart. Each slice is judged on its own, so the circles can differ in size and centre from slice to slice.

Tolerance zone. The zone is the ring between two concentric circles in the cross-section plane. The ring has no fixed position, so a slightly off-centre but round outline passes.

Detail B · How an inspector checks it

How Circularity is inspected

A roundness tester rotates the part, or its probe, and records the radius around the circle. On a coordinate measuring machine, probe points at evenly spaced angles in one plane and compute the radial spread. Three-point V-block checks with an indicator can mislead on lobed shapes, because a part with an odd number of lobes can look round in a V-block.

How to measure Circularity

Circularity is measured with the instruments below; the table says how each is set up and what you write down.

Instrument Set-up What is recorded
Roundness tester Part rotated on a spindle, stylus traces each section Radial range of the trace
CMM Points taken around one section, a circle is fitted Spread about the fitted circle
V-block and dial indicator Part turned in the block, indicator read Indicator range (a rough check only)

Circularity compared with Cylindricity

Commonly confused with The difference
Cylindricity Circularity applies to each cross-section on its own; cylindricity controls the whole cylinder, including taper and bow.
Detail C · Entering it in the tool

How to enter Circularity in the tool

In the characteristic table, press GD&T on the row, choose the Circularity symbol, type the tolerance. The tool writes the frame into the Requirement column as text, and the report prints it. For example, a frame with a tolerance of 0.02 is written as ○ | 0.02 on screen and as CIRC | 0.02 in the PDF report, where the standard PDF fonts have no GD&T glyphs.

Datum reference: No. It is a form tolerance and has no datum.

Worked example: reading and judging a Circularity frame

The bundled sample drawing has no feature control frames, so this example uses an invented frame, written by the tool as ○ | 0.02. The tolerance is 0.02, which gives a zone 0.02 wide. The inspector measures the feature and finds a Circularity error of 0.016. That is less than 0.02, so the feature is in tolerance with room to spare. A second part measures 0.024. That is more than 0.02, so it is out of tolerance by 0.004. The report row for the second part carries the frame text as the requirement, 0.024 as the result, a verdict in words and a note saying what happened to the part.

Measured Circularity Tolerance Verdict
0.016 0.02 In tolerance
0.024 0.02 Out of tolerance

The numbers are generated from the example the tool itself uses for this symbol, so they stay in step with the frame text shown above. Both are illustrations, not data from a real part.

Detail D · Common mistakes

Mistakes to avoid with Circularity

Mixing it up with diameter or with runout. Circularity ignores size and ignores where the axis is. If the drawing needs the whole cylinder controlled along its length, that is cylindricity, not circularity. Check enough cross-sections: one slice can pass while another is out.

Does Circularity need a datum?
No. It is a form tolerance and has no datum.
Which group of controls is Circularity in?
It is a Form control. The groups are form, profile, orientation, location and runout, and they differ in what they relate the feature to.
How do you measure Circularity?
One common method is the Roundness tester: Part rotated on a spindle, stylus traces each section, and the inspector records: Radial range of the trace. The method table on this page lists the alternatives and what each records.
What is Circularity commonly confused with?
Cylindricity. Circularity applies to each cross-section on its own; cylindricity controls the whole cylinder, including taper and bow.
How do I enter Circularity in an inspection report?
Press GD&T on the row in the characteristic table, pick the symbol, type the tolerance and any modifier or datums. The tool writes the frame into the Requirement column as text, and the report prints it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds