Engineering drawing symbols: dimensions, holes, tolerances and notes

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

Engineering drawings use a small set of symbols: a circle with a slash for diameter, R for radius, a boxed value for a basic dimension, brackets for a reference, geometric tolerance symbols in feature control frames, and special marks for holes and surface finish. The table lists the ones inspectors meet most.
Detail A · Table

Common symbols

Symbol Meaning More
Ø Diameter
R Radius
Boxed value Basic dimension basic dimension
(value) Reference dimension reference dimension
⌴ ⌵ ↧ Counterbore, countersink, depth hole callouts
Frame with symbol Geometric tolerance feature control frame
Letter in a box Datum feature datums
Check mark with lines Surface finish surface finish

Threads

A thread callout such as M10 x 1.5 gives the nominal diameter and pitch; the tolerance class follows after a dash. Check the thread with the gauge your customer names.

Detail B · In a report

What gets a balloon

A symbol that carries a requirement gets a balloon: a hole, a tolerance, a thread, a finish. Notes and datum labels do not unless they carry a requirement.

Common mistakes

  • Mixing up a reference dimension and a tolerance.
  • Missing a thread callout in a note.

Symbols you will see in feature control frames

The fourteen geometric characteristic symbols (straightness, flatness, circularity, cylindricity, profile of a line, profile of a surface, parallelism, perpendicularity, angularity, position, concentricity, symmetry, circular runout and total runout) are shown on the GD&T chart with a page for each. The material condition modifiers M and L are explained on their own page.

Dimension symbols

A diameter sign marks a circular feature or a cylindrical tolerance zone. R marks a radius. A square sign marks a square feature. A box around a number marks a basic dimension. An arc over a number marks an arc length. A slash through a dimension marks it as not to scale on older drawings.

Section and view marks

Capital letters with arrows show where a section is cut and which way it is viewed. A circle with a letter marks a detail view. These do not carry requirements, but they tell you where to find a dimension.

Weld and finish symbols

Welding symbols have their own standard and are outside what this site covers. Surface finish symbols are explained on their page.

How to use this page

Treat it as a quick lookup. Where a symbol is not covered, find its meaning in the drafting standard the drawing cites rather than guessing, because a wrong reading changes how the part is checked.

Worked example on the sample part

The sample drawing uses four symbols you will meet constantly. The diameter sign appears on five of its seven balloons: the 110.0 diameter (balloon 3), the 70.0 and 30.00 diameters (balloons 4 and 5), and the 9.0 holes and 90.0 bolt circle (balloons 6 and 7). The plus-minus tolerance sign gives the symmetric limits on balloons 1, 2, 3, 6 and 7. The unilateral form, plus 0.03 over zero, appears on balloons 4 and 5. The quantity prefix 4X appears on balloon 6. Each of these changes how the report row is filled, and the generated table shows all of them.

Report rows for the sample drawing
No.RequirementMinMaxResultVerdict
120.0 ±0.219.820.220.08IN TOL
270.0 ±0.369.770.369.91IN TOL
3⌀110.0 ±0.1109.9110.1110.04IN TOL
4⌀70.0 +0.03/070.070.0370.02IN TOL
5⌀30.00 +0.02/030.0030.0230.01IN TOL
64X ⌀9.0 ±0.1 THRU8.99.19.05IN TOL
7⌀90.0 ±0.1 B.C.89.990.190.03IN TOL

Table: rows produced by the tool for the sample drawing. The measured results are made-up demo values.

How symbols combine

A single callout often stacks several: a quantity, a diameter sign, a size, a tolerance and an instruction. Read them in order and write down what each asks you to measure. If a callout includes a feature control frame, read it separately as its own characteristic: see how to read a feature control frame.

Common marks beyond the table

Mark Meaning Where covered
Triangle on a surface Datum feature symbol, often with a letter in a box Datums
Circle with a letter on a leader Detail view marker This page
Arrow with a letter Section view marker This page
Wavy leader or break line The part is shown shortened This page
Arrowhead dimension line The extent of a dimension This page
Diameter with a slash Diameter Table above
Underlined number Not to scale on older drawings Check the drawing's notes

Mistakes inspectors make

  • Taking a dimension from a detail view and missing that its scale differs from the full view.
  • Reading a section view's hatching as part of a dimension.
  • Missing the underline that marks a value as not to scale and then scaling from the drawing.
  • Treating a datum triangle as a weld or finish mark.
Where do I find the GD&T symbols?
See the chart.
What do the symbols on an engineering drawing mean?
They are shorthand for sizes, shapes, tolerances and instructions: a slashed circle is a diameter, R is a radius, a box marks a basic dimension and a framed symbol is a geometric tolerance. The table on this page lists the common ones with links.
How do I read a section view?
A section view shows the part as if cut along a marked line, with hatching on the cut material. Find the cutting-plane arrows on another view, read the letter, and use the dimensions on the section for features inside.
Where do I find GD&T symbols?
The fourteen geometric characteristic symbols are charted on the GD&T page, each with its own page on meaning, inspection and entry in a report.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds