Hole callouts: counterbore, countersink, depth and diameter symbols

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

A hole callout packs several requirements into one line. The counterbore symbol looks like a square-bottomed cup, the countersink symbol like a V, the depth symbol like an arrow pointing down at a line, and the diameter symbol like a circle with a slash. Each one is a separate characteristic when you inspect.
Detail A · Symbols

Symbol table

Symbol Name What it gives
Ø Diameter Size of the hole
⌴ Counterbore Larger diameter and depth for a flat-bottomed recess
⌵ Countersink Cone angle and diameter at the surface
↧ Depth How deep a feature goes
Detail B · One callout, several rows

Split it

A callout such as "4X Ø6.6 THRU, ⌴ Ø11 depth 6.5" gives these characteristics, shown as an example:

Part Characteristic
4X Four holes
Ø6.6 THRU Hole diameter, with limits
⌴ Ø11 Counterbore diameter
depth 6.5 Counterbore depth

Balloon it once and record each result, or split into sub-numbers (6.1, 6.2...) so every hole has its own row.

Common mistakes

  • Measuring the hole and forgetting the counterbore.
  • Ignoring a tolerance printed beside only one part of the callout.

Reading the callout in order

Callouts read from the hole outward. The first number is the hole diameter, with its tolerance. A thru note says it goes through. A symbol for counterbore or countersink follows, with its larger diameter, and a depth for a counterbore or an angle for a countersink. A quantity prefix such as 4X applies to the whole line.

A countersink example

A callout giving a diameter, a countersink symbol, a larger diameter and an angle of 90 degrees describes a conical recess so a flat-head screw sits flush. The characteristics are the hole diameter, the countersink diameter at the surface and the angle.

How the rows come out

On the sample the quantity callout is one balloon with four results, and you may split it into sub-numbers with the tool. For a counterbore the tool leaves you to choose: one balloon with the whole callout, or a balloon for each part, which gives a clearer report because each part is checked with a different instrument: a pin gauge for the hole, a caliper or depth gauge for the recess.

Threaded holes

A threaded hole callout gives the thread size and pitch and often a depth for the thread and for the drilled hole. Report the thread with the gauge the customer names, and the depth separately.

Mistakes to avoid

  • Checking the hole and forgetting the recess.
  • Using a depth measured from the wrong surface.
  • Applying a tolerance printed for the hole to the counterbore.

Worked example on the sample part

The sample has one hole callout, 4X diameter 9.0 plus or minus 0.1 THRU, balloon 6. The generated table gives its limits as 8.9 to 9.1 and the demonstration result as 9.05, in tolerance. It is a plain through hole: no counterbore, countersink or depth. That keeps it a good model for the simplest case: one characteristic, one quantity, one instruction. Compare it with a more complex callout in the table below.

Callout Characteristics to record
4X 9.0 plus or minus 0.1 THRU (sample) Hole diameter, four results
4X 6.6 THRU, CBORE 11 DP 6.5 Hole diameter, counterbore diameter, counterbore depth
4X 6.6 THRU, CSK 12.4 x 90 deg Hole diameter, countersink diameter, countersink angle
M8 x 1.25 DP 14 Thread size and pitch, thread depth

The second, third and fourth callouts are examples to show the splitting: they are not on the sample drawing.

Measuring each part

A hole diameter is checked with a pin gauge, an air gauge, a bore gauge or a CMM, chosen to match the tolerance. A counterbore diameter is a caliper or bore gauge job and its depth is a depth gauge or height gauge reading from the surface the drawing names. A countersink diameter and angle are checked with a countersink gauge. A thread is checked with the thread gauge the customer names, normally a go and no-go pair.

Where the depth is measured from

Depth is measured from the surface the callout points to, to the bottom of the feature. For a counterbore it is the depth of the flat bottom. For a drilled hole with a point, the depth normally excludes the cone unless the drawing says otherwise. Check the notes.

Mistakes inspectors make

  • Measuring from a different surface than the one the callout names.
  • Measuring a countersink at the wrong diameter: it is taken at the surface.
  • Treating an M8 callout as the hole size: the callout is the thread, and the drill size is a separate matter that is often not a requirement.
  • Missing that a tolerance printed beside only one part of the callout does not apply to the others.
What is the counterbore symbol on a drawing?
A cup with a flat bottom, followed by the recess diameter and depth.
What is the countersink symbol?
The countersink symbol looks like a V or a cone seen from the side, followed by the diameter at the surface and the included angle, for example 12.4 by 90 degrees. Record the diameter and the angle as separate characteristics.
What does the depth symbol mean on a drawing?
The depth symbol, an arrow pointing down at a line, introduces how deep a feature goes, measured from the surface the callout points to. It can follow a hole, counterbore or thread callout, and it is its own characteristic.
How do I split a hole callout into report rows?
Give each distinct requirement its own result: hole diameter, counterbore diameter, counterbore depth or countersink angle. Apply the quantity prefix to each, either as one balloon with several results or as sub-numbers.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds