What is first article inspection, and when is it asked for?

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

A first article inspection is a documented check that the first part made by a new or changed process actually meets every requirement on the drawing and purchase order. The result is a report with one line per characteristic: what was required, what was measured, and whether it was acceptable.
Detail A · The idea

What it is for

Before a supplier makes a full batch, the customer wants evidence that the process can make the part right. The first article is measured completely, not sampled, and the measurements are written down against the drawing. If something is out, it is found while only one part exists.

The report is evidence for the customer. It is not a certification and a file cannot make a part conform; the checking is what counts, and the report records it.

Detail B · When it is usually requested

Typical triggers

Customers decide this in their purchase terms, so always read yours. Commonly it is asked for when:

  • a part is made for the first time, or by a supplier for the first time;
  • the drawing or specification changes in a way that touches the part;
  • the process, tooling or location of manufacture changes;
  • production stopped for a long period and restarted;
  • a nonconformance led to a corrective action that needs proof.

Which of these applies, and how often, comes from the customer. This guide cannot tell you what yours requires.

Detail C · What the report holds

Three kinds of information

Reports in the common three-part layout record, first, the part and its identity, second, the materials, processes and tests that were used, and third, the characteristic-by-characteristic measurements. This site covers the third part: ballooning the drawing and filling the characteristic table. The Form 3-style report explained walks through the columns.

The table has one row per balloon. Each row says what the drawing requires, what you measured, and what you used to measure it.

Detail D · Doing it

A sensible order of work

  1. Balloon the drawing so every characteristic has a number (method).
  2. Type or capture the requirement and tolerance for each row.
  3. Measure the part and enter the result. A numeric result is checked against the limits; an attribute check can be marked pass or fail.
  4. Note the gauge or instrument used.
  5. Review every row that is out of tolerance before you issue the report, and raise a nonconformance note for each one.
FLANGED BUSHING - SAMPLE PARTDRAWN FOR balloonmydrawing.com SHEET 1 OF 1 MMSECTION A-AFRONT VIEW20.0 ±0.270.0 ±0.3⌀110.0 ±0.1⌀70.0 +0.03/0⌀30.00 +0.02/04X ⌀9.0 ±0.1 THRU⌀90.0 ±0.1 B.C.1234567
Figure 1. A ballooned sample drawing. Each of the seven numbers becomes a row in the report.
Report rows for the sample drawing
No.RequirementMinMaxResultVerdict
120.0 ±0.219.820.220.08IN TOL
270.0 ±0.369.770.369.91IN TOL
3⌀110.0 ±0.1109.9110.1110.04IN TOL
4⌀70.0 +0.03/070.070.0370.02IN TOL
5⌀30.00 +0.02/030.0030.0230.01IN TOL
64X ⌀9.0 ±0.1 THRU8.99.19.05IN TOL
7⌀90.0 ±0.1 B.C.89.990.190.03IN TOL

Table: rows produced by the tool for the sample drawing. The measured results are made-up demo values.

Worked example on the sample part

Take the sample flanged bushing. A first article inspection of it means measuring every characteristic on its drawing on the first part: seven rows, with limits from the printed tolerances. The table below is that record, with demonstration measurements.

Report rows for the sample drawing
No.RequirementMinMaxResultVerdict
120.0 ±0.219.820.220.08IN TOL
270.0 ±0.369.770.369.91IN TOL
3⌀110.0 ±0.1109.9110.1110.04IN TOL
4⌀70.0 +0.03/070.070.0370.02IN TOL
5⌀30.00 +0.02/030.0030.0230.01IN TOL
64X ⌀9.0 ±0.1 THRU8.99.19.05IN TOL
7⌀90.0 ±0.1 B.C.89.990.190.03IN TOL

Table: rows produced by the tool for the sample drawing. The measured results are made-up demo values.

Common mistakes

  • Reporting from a drawing revision that is not the current one.
  • Leaving blank cells without a reason; mark a reference dimension as reference rather than leaving it empty.
  • Mixing units in one table without saying so.
  • Rounding a result so it falls inside the limits. Report what the instrument showed.

FAI, FAIR and first piece: the terms

Term Meaning
FAI First article inspection: the inspection itself
FAIR First article inspection report: the record of it
First piece inspection A common term for the same idea, often used in machine shops
First off Shop-floor term for the first part from a set-up

Are FAI and FAIR the same?

They are closely related but not identical: the FAI is the activity and the FAIR is the report that records it. People use them interchangeably in conversation, which is fine until a purchase order asks for one specifically.

What does a first article inspection include?

Every characteristic on the drawing, measured and recorded; the materials and special processes that went into the part; and the identity of the part, drawing and revision. See the procedure, the checklist and a worked example.

Is a first article report the same as a certificate of conformance?
No. A certificate states that the supplier asserts conformance. A first article report shows the measurements behind it, characteristic by characteristic.
Who decides when I need one?
Your customer, through the purchase order or quality agreement. This site cannot tell you what yours requires.
Does the free tool produce a report my customer will accept?
It produces a report in an AS9102-style Form 3 layout. Whether it meets your customer's format is something you confirm with them.
What is first article inspection?
It is a complete check of the first part, or first parts, from a new process, measured against every requirement of the drawing and recorded in a report, to show the process can make conforming parts.
What does FAIR stand for in manufacturing?
FAIR stands for first article inspection report, the record of the inspection. FAI is the inspection itself, and the two terms are often used interchangeably.
Are FAI and FAIR the same?
Closely related, not identical: the FAI is the activity and the FAIR is the report that records it.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds