First article inspection report example: a complete worked report

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

This is a complete example of the characteristics part of a first article inspection report, in a Form 3-style layout: a header strip and one row for each of seven ballooned dimensions, with the requirement, the limits, the measured result and an in-or-out verdict. Every number below was produced by the tool, and the measured values are made up for the example.
Detail A · The header

Identify the part first

Field Sample entry
Part number FB-2210
Part name Flanged bushing (sample part)
Revision A
Report identifier SAMPLE-001
Prepared by Balloon My Drawing
Date 2026-11-19

On a real report the serial or lot number and the person who prepared it matter. They are optional in the tool, so you can export now and complete them later.

Detail B · The characteristics

Seven rows, one per balloon

FLANGED BUSHING - SAMPLE PARTDRAWN FOR balloonmydrawing.com SHEET 1 OF 1 MMSECTION A-AFRONT VIEW20.0 ±0.270.0 ±0.3⌀110.0 ±0.1⌀70.0 +0.03/0⌀30.00 +0.02/04X ⌀9.0 ±0.1 THRU⌀90.0 ±0.1 B.C.1234567
Figure 1. The sample drawing. The numbers match the rows below.
Report rows for the sample drawing
No.RequirementMinMaxResultVerdict
120.0 ±0.219.820.220.08IN TOL
270.0 ±0.369.770.369.91IN TOL
3⌀110.0 ±0.1109.9110.1110.04IN TOL
4⌀70.0 +0.03/070.070.0370.02IN TOL
5⌀30.00 +0.02/030.0030.0230.01IN TOL
64X ⌀9.0 ±0.1 THRU8.99.19.05IN TOL
7⌀90.0 ±0.1 B.C.89.990.190.03IN TOL

Table: rows produced by the tool for the sample drawing. The measured results are made-up demo values.

How to read it:

  • Min and Max are the limits worked out from the printed tolerance. Row 1, 20.0 plus or minus 0.2, runs from 19.8 to 20.2.
  • Row 4 is a unilateral tolerance, 70.0 with plus 0.03 and zero below, so the limits are 70.0 and 70.03.
  • Row 6 is a quantity callout, 4X. You can report it as one balloon with four results, or split it into 6.1 to 6.4 and give each hole its own row.
  • Verdict is always in words, so the report still reads correctly when photocopied in greyscale.
Detail C · What a reviewer checks

Before you issue it

  1. Every balloon number from 1 to the last appears once on the drawing and once in the table.
  2. Every row has limits that can be checked against the drawing.
  3. Results are recorded to the same precision as the tolerance.
  4. A note is written against every out-of-tolerance row.
  5. The tooling column says what was measured with.

Get this example

Common mistakes in example reports

  • Copying an example's values into a real report. These results are demonstration values only.
  • Leaving the tooling column empty.
  • Rounding a result so it falls inside the limits.

Why these seven rows

The sample part has seven characteristics: two linear dimensions with bilateral tolerances, a diameter with a bilateral tolerance, two diameters with unilateral tolerances, a hole pattern with a 4X quantity and a bolt circle. Together they show the situations a reader meets most: bilateral and unilateral tolerances and a quantity callout. Each of those is explained in its own guide, linked from the index.

What a reader looks at first

A reviewer scans the verdict column for anything that is not within tolerance, then reads the notes against those rows. If every row is in tolerance, they check a handful at random against the drawing, especially tight tolerances and anything with a quantity.

The same report in Excel

The Excel version has the same columns, with the limits as numbers, so a quality system can import them. The download above gives both forms. Remember the measured values are invented, so do not file this as a record of any real part.

Reading the table row by row

Row 1, 20.0 plus or minus 0.2. Limits 19.8 to 20.2. Demonstration result 20.08, in tolerance with 0.12 spare on the upper side.

Row 2, 70.0 plus or minus 0.3. Limits 69.7 to 70.3. Result 69.91, in tolerance.

Row 3, diameter 110.0 plus or minus 0.1. Limits 109.9 to 110.1. Result 110.04, in tolerance.

Row 4, diameter 70.0 plus 0.03 and zero below. Limits 70.00 to 70.03. Result 70.02, in tolerance with 0.01 spare. This is the tightest row on the sheet, so it is the one a reviewer checks first.

Row 5, diameter 30.00 plus 0.02 and zero below. Limits 30.00 to 30.02. Result 30.01, in tolerance. Note that it is printed to two decimals, so its result is recorded to two decimals.

Row 6, 4X diameter 9.0 plus or minus 0.1 THRU. Limits 8.9 to 9.1. Result 9.05. A real report would show four results here, one per hole.

Row 7, diameter 90.0 plus or minus 0.1 on a bolt circle. Limits 89.9 to 90.1. Result 90.03.

What to add for a real report

The sample report has no nonconformance, so the nonconformance column is empty. On a real one, any out-of-tolerance result gets a reference number and a note: what was found, who reviewed it and what was decided. A report with an unexplained failure is usually sent back.

Mistakes people make with worked examples

  • Copying a layout without the logic. Understand why each column is there, then adapt.
  • Recording a result with fewer decimals than the tolerance, so the verdict cannot be checked.
  • Believing a clean report is a good report: a clean report that misses a characteristic is worse than an honest one with a noted failure.
Is this an official report?
No. It is a worked example in an AS9102-style Form 3 layout, with invented measurements.
Can I use it as a template?
Use the blank template instead, or open your own drawing in the tool.
What does a completed first article inspection report look like?
A header that identifies the part, then one row per characteristic with the requirement, limits, measured result and verdict, plus the tooling and a nonconformance reference where needed. The example on this page has seven rows built from the sample drawing.
Where can I get a first article inspection report sample?
The sample report on this page downloads as PDF and Excel. Its measured values are invented, so use it to see the layout and the logic, not as data for a real part.
What should be in a first article inspection report?
Part identity, every characteristic with its requirement, limits, result and verdict, the tooling used, the materials and processes, and notes for anything out of tolerance. Your customer may require a specific layout, which then takes priority.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds