ISO 2768 general tolerances: classes, mK and how to read them
What the designation says
| Part of the note | Meaning |
|---|---|
| ISO 2768 | The standard being invoked |
| First letter, f / m / c / v | Class for linear and angular dimensions: fine, medium, coarse, very coarse |
| Second letter, H / K / L | Class for geometrical tolerances, from tightest to loosest |
So ISO 2768-mK means medium for sizes and angles, and class K for form and orientation. The standard has two parts: one for linear and angular dimensions, one for geometrical tolerances without individual indication.
The tables
The permitted deviation depends on the nominal size range and on the class. The tables belong to the standard, sold by ISO and national bodies, and we do not reprint them. Secondary sources that reproduce them do not always agree with each other, which is why we point you to the standard. We checked two size ranges across several published tables and found these figures repeated, but did not verify them against the standard, so confirm before relying on them:
| Nominal size | Class f | Class m | Class c | Class v |
|---|---|---|---|---|
| 0.5 to 3 mm | 0.05 | 0.1 | 0.2 | n/a |
| over 3 to 6 mm | 0.05 | 0.1 | 0.3 | 0.5 |
Values are plus or minus, in millimetres, as repeated by several published reproductions (see sources); they are not taken from the standard. For a 50 mm dimension in class m, read the row for that size range in your own copy of the standard. We deliberately do not state it from memory.
In a report
A dimension with no tolerance of its own gets limits from the general tolerance in the title block. The tool lets you set that rule once in Tolerances and parts and works the limits out for each balloon. You still enter the values from your copy of the standard or title block.
Common mistakes
- Applying general tolerance to a basic dimension. A basic dimension has none; see basic dimension.
- Assuming ISO 2768 applies because the drawing is metric. It applies only if the drawing or contract invokes it.
- Using an old edition.
A worked reading
A drawing carries the note "General tolerances ISO 2768-mK" and a dimension of 36 with no tolerance. To find its limits you read the linear table of the standard, in the m column, on the row for the size range that contains 36, and apply the value as plus or minus. A second dimension, a flatness requirement with no frame, falls under class K for geometry and is read from the geometrical table. The tool does the arithmetic once you have the value: enter it in the Tolerances and parts dialog.
What the standard does not cover
General tolerances give a baseline for features with no individual tolerance. They do not apply where a feature has its own tolerance or a frame, and they do not replace a tolerance that the function of the part needs. They also say nothing about surface finish.
Where to buy it
The standard is published by ISO and by national standards bodies. The ISO catalogue page is linked in the sources. A purchased copy is the only reliable source for the tables, and it is cheap compared with scrapping parts because of a mistyped value.
How our general-tolerance feature applies it
The tool does not contain the ISO 2768 tables, and it does not decide a class for you. Its general-tolerance setting works from a rule you enter yourself, keyed to the number of decimal places printed in the dimension, for example one decimal gets one value and two decimals another. You read the values from your own copy of the standard or from the title block, type them in once, and the tool then works the limits for every balloon that has no tolerance of its own. Each such row records that a general tolerance was applied.
This matters for the sample drawing. Its seven dimensions all carry their own tolerance, so none of them would use a general tolerance. If a dimension printed as 36.50 had no tolerance and the rule for two decimals were plus or minus 0.25, the limits would come out as 36.25 to 36.75, and a measured 36.78 would be 0.03 outside. The numbers are an illustration of the mechanism, not values taken from the standard.
How to read a callout such as ISO 2768-mK
- Find the note in or next to the title block. It may read "General tolerances ISO 2768-mK" or give the same thing in another form.
- Split the designation: the letter after the hyphen is the class for sizes and angles, and the capital letter after it is the class for geometry.
- Find the nominal size of the dimension you need and the row of the linear table that covers it.
- Read the value in the column for your class and apply it as a plus-minus.
- For features with no frame, such as flatness or perpendicularity, read the geometrical table for class K in the same way.
- Record the limits, and note on the report row that a general tolerance applied.
A dimension with its own tolerance is not covered by the standard. A basic dimension is not covered either, because its frame gives its tolerance.
The unverified-values caveat
The two size ranges shown above come from published reproductions that agree with each other, but they are not the standard, and at least one reproduction we found disagreed on some values. We have not compared them with a purchased copy. They are shown to illustrate the shape of the table and must not be used as limits on a real inspection. If you need a number, take it from the standard your drawing cites, in the edition it cites.
Mistakes inspectors make
- Using a table from a web page instead of the standard, and inheriting its typos.
- Applying a class the drawing never named. If the title block says nothing, ISO 2768 does not apply.
- Mixing up the two letters: the lowercase one is for sizes, the capital for geometry.
- Using the linear table for angles.
- Passing a part on a general tolerance for a feature that has its own tolerance.
- What is ISO 2768-mK?
- Medium linear class and geometrical class K.
- What is the ISO 2768 medium tolerance for 50 mm?
- It is in the table of the standard; we do not state the figure here because we could not verify it.
- Does it apply to every drawing?
- Only where the drawing, title block or contract calls for it.
- What are the ISO 2768 tolerance classes?
- For linear and angular dimensions the classes are f, m, c and v, from fine to very coarse. For geometrical tolerances they are H, K and L, from tightest to loosest. A callout names one of each, such as m and K.
- Does ISO 2768 apply to every metric drawing?
- No. It applies only when the drawing, title block or contract names it. Without that note, there is no general tolerance from this standard, and a dimension with no tolerance needs a different rule from the drawing.
- Where can I buy ISO 2768?
- The standard is published by ISO and national standards bodies. The ISO catalogue entry is linked in the sources. A purchased copy is the reliable way to get the tables, and ours deliberately does not reproduce them.
Sources
- ISO 2768-1:1989, General tolerances: https://www.iso.org/standard/7748.html (read 2026-11-19)
- General Tolerances (reproduction): https://vibromera.eu/calculators/general-tolerances-iso2768-1/ (read 2026-11-19)
- ISO 2768 general tolerances table: https://www.ziko-technik.de/en/allgemeintoleranzen.html (read 2026-11-19)