General tolerances in the title block: what applies when a dimension has no tolerance

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

When a dimension on a drawing has no tolerance of its own, the general tolerance printed in the title block, or in the standard the title block names, applies to it. A dimension is not tolerance-free just because none is printed beside it, except a basic dimension, which gets its tolerance from a feature control frame.
Detail A · Reading the block

Where to look

The title block or general notes carry a line such as "unless otherwise specified, tolerances are: X.X plus or minus 0.5, X.XX plus or minus 0.25", or cite a standard like ISO 2768. Some shops key the tolerance to the number of decimal places, others to size ranges. The drawing decides; the examples here are made up.

Printed value Decimals Example rule Limits
12.5 1 plus or minus 0.5 12.0 to 13.0
12.50 2 plus or minus 0.25 12.25 to 12.75
12.500 3 plus or minus 0.125 12.375 to 12.625
Detail B · In the tool

Enter it once

Open Tolerances and parts, pick the by-decimals rule, and give the values from the title block. Each balloon with no tolerance of its own then gets limits computed from the printed value, and says in the notes that a general tolerance applied.

Common mistakes

  • Reading the title block of the wrong sheet.
  • Applying it to angles with a linear rule.
  • Counting decimal places on a converted value.

Tolerance by size range

Some title blocks give a tolerance by size range rather than by decimal places: for example, up to a certain size one value, and above it a larger one. The drawing is the authority, but the method is the same: find the nominal on the table, read the tolerance and apply it as plus and minus. If the block cites a standard, such as ISO 2768, you need your copy of the standard for the values. See ISO 2768.

A worked report row

A dimension printed as 36.50 with the block rule "two decimals: plus or minus 0.25" has limits 36.25 to 36.75. A measured 36.78 is 0.03 outside the upper limit and fails. In the tool the row is filled automatically once the rule is set, and a note records that the general tolerance was applied.

Angles and geometry

Angular dimensions usually get their own line in the block. Geometric tolerances without a frame may be covered by a general geometric class, again from the standard the block cites. Check what the block covers before assuming it applies to everything.

When the block and the dimension disagree

A tolerance beside the dimension always beats the title block. A basic dimension has no tolerance of its own and is not covered by the block.

Worked example from the sample part

All seven dimensions on the sample carry their own tolerance, so none of them uses a general tolerance. To see the mechanism, imagine the 70.0 dimension had been printed with no tolerance and the title block said one decimal is plus or minus 0.5. The limits would be 69.5 to 70.5. The result of 69.91 would then be in tolerance against those limits, whereas against its actual printed tolerance of plus or minus 0.3 it is in tolerance against 69.7 to 70.3. The wider general tolerance would accept values that the real drawing rejects, which is why a printed tolerance always beats the block.

Report rows for the sample drawing
No.RequirementMinMaxResultVerdict
120.0 ±0.219.820.220.08IN TOL
270.0 ±0.369.770.369.91IN TOL
3⌀110.0 ±0.1109.9110.1110.04IN TOL
4⌀70.0 +0.03/070.070.0370.02IN TOL
5⌀30.00 +0.02/030.0030.0230.01IN TOL
64X ⌀9.0 ±0.1 THRU8.99.19.05IN TOL
7⌀90.0 ±0.1 B.C.89.990.190.03IN TOL

Table: rows produced by the tool for the sample drawing. The measured results are made-up demo values.

Setting it up in the tool

Open Tolerances and parts, choose the by-decimals rule and enter the value for each number of decimal places from the title block. The setting is saved with the project. Each balloon with no tolerance of its own then gets limits computed from its printed value, and its row notes that a general tolerance applied. Rows with their own tolerance are untouched.

Common title-block forms

Title-block wording How to apply it
Tolerances by decimal places Match the decimals printed in the dimension
Tolerances by size range Find the nominal's range and read the value
A standard named, such as ISO 2768 Read the class and the table in your copy of the standard
An angular tolerance Use it for angles only

Mistakes people make

  • Counting decimals after converting units. Count them as printed.
  • Applying the block to a dimension that has its own tolerance.
  • Applying the block to a basic dimension or a reference dimension.
  • Using the block from a different sheet or an older revision of the drawing.
What tolerance applies when a dimension has no tolerance?
The general tolerance in the title block or the standard cited there.
Does it apply to a basic dimension?
No.
What is a general tolerance?
A general tolerance is the tolerance that applies to every dimension on a drawing that has no tolerance of its own. It is printed in the title block or given by a standard cited there. It saves repeating the same plus-minus on every dimension.
Where do I find the general tolerance on a drawing?
In the title block or the general notes, often worded 'unless otherwise specified' or naming a standard. If it is on one sheet of a multi-sheet drawing, it normally applies to all of them, but check the notes.
What is the difference between a general tolerance and a title-block tolerance?
They are the same idea. 'Title-block tolerance' describes where it is printed, and 'general tolerance' describes what it does: it applies to dimensions with no tolerance of their own.
How do I enter a general tolerance in the tool?
Open Tolerances and parts, choose the by-decimals rule, and type the values from your title block. The tool then computes limits for every balloon that has no tolerance of its own.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds