How to read an engineering drawing as a machinist or inspector
Seven steps
- Title block: part number, revision, units, scale, material.
- General notes: finishes, deburr, general tolerance block.
- Views: front, top, side and sections; find where each feature appears.
- Datums: which surfaces everything is measured from.
- Dimensions and tolerances: nominal, plus and minus, limits.
- Feature control frames.
- Count characteristics: that is the number of balloons you will need.
The sample part
Common mistakes
- Reading dimensions before the notes.
- Not checking units.
- Missing a revision change.
Where the information hides
Beginners look at the views and miss the text. Most of what changes how a drawing is read is in the title block, the general notes and the revision table. The title block gives the units, the projection method and the general tolerance. The notes may call for a finish, a heat treatment, a deburr or a thread standard that no view shows. The revision table tells you what changed since the previous issue, which is the first place to look when a part from an earlier run disagrees with the print.
Views and sections
A front, top and side view show the part from different directions. A section view shows an imaginary cut and reveals the inside: hatching marks the cut material. A detail view shows a small area enlarged so tight dimensions fit. If a dimension appears only in a detail view, it applies to that feature in the full view too.
Units and scale
Check the units before anything else: millimetres and inches look alike on the page. Do not scale from the drawing: scale is for orientation only, and a dimension governs over how long a line looks.
Dimensions to count
Each dimension, thread, finish and note that carries a requirement is a characteristic and gets a balloon. Counting them first tells you how big the job is. On the sample part there are seven.
Mistakes to avoid
- Measuring from a datum the drawing does not name.
- Ignoring a note on a different sheet.
- Treating a reference dimension as a requirement.
Worked example: reading the sample drawing
Follow the seven steps on the bundled sample. The title block gives the part and revision. There are no general notes that change the dimensions. The views show the part from the front and one side. There are no datums, because the sample has no feature control frames. The dimensions and tolerances are the seven in the table below. There are no frames to read. The count of characteristics is seven, so the job needs seven balloons, plus four more rows if the 4X callout is split.
| No. | Requirement | Min | Max | Result | Verdict |
|---|---|---|---|---|---|
| 1 | 20.0 ±0.2 | 19.8 | 20.2 | 20.08 | IN TOL |
| 2 | 70.0 ±0.3 | 69.7 | 70.3 | 69.91 | IN TOL |
| 3 | ⌀110.0 ±0.1 | 109.9 | 110.1 | 110.04 | IN TOL |
| 4 | ⌀70.0 +0.03/0 | 70.0 | 70.03 | 70.02 | IN TOL |
| 5 | ⌀30.00 +0.02/0 | 30.00 | 30.02 | 30.01 | IN TOL |
| 6 | 4X ⌀9.0 ±0.1 THRU | 8.9 | 9.1 | 9.05 | IN TOL |
| 7 | ⌀90.0 ±0.1 B.C. | 89.9 | 90.1 | 90.03 | IN TOL |
A reading order for a busier drawing
- Count the sheets and note the revision of each.
- Read every note, including those at the bottom and on other sheets.
- Find the datum letters and what they label.
- Work through each view, ticking each dimension you have read.
- Read each frame as its own item.
- Count the characteristics and compare with your balloons.
- Ask about anything unclear before you start measuring.
Different drawing styles
Older drawings may use inches, fractions and different tolerance conventions. Imported drawings from other countries may use first-angle projection, where the views are arranged differently from third-angle. The projection symbol in the title block tells you which. Mixing them up flips your idea of which side a feature is on.
Mistakes people make
- Starting with the largest view and missing a detail view.
- Not reading the general notes.
- Measuring a feature that a section view shows as internal from the wrong side.
- Skipping the revision table.
- How do I read a blueprint?
- Use the seven steps above.
- How do I read a blueprint?
- Read the title block and notes first, then the views, then each dimension and its tolerance, then any frames and datums. Count the characteristics and ask about anything unclear before measuring.
- What is the first thing to look at on an engineering drawing?
- The title block: part number, revision, units, scale and projection. A wrong revision or the wrong units wastes everything after it.
- What is the difference between first-angle and third-angle projection?
- They arrange the views differently. In third-angle, common in North America, the right view is placed on the right. In first-angle it is on the left. The title block symbol tells you which one the drawing uses.
- How do I read a section view?
- Find the cutting-plane line with its arrows on another view, match the letter and read the section as if the part were cut along that line. Hatching marks the cut material.