How to read a CMM report: columns, deviation and out-of-tolerance

Last reviewed 19 November 2026 · Written by Paul, who also builds and supports the tool

A CMM report lists, for each feature measured, the nominal value from the drawing, the plus and minus tolerances, the measured value, the deviation (measured minus nominal) and whether it is out of tolerance. Read across a line: the measured value should sit between nominal plus the lower tolerance and nominal plus the upper tolerance.
Detail A · Column glossary

What each column means

Column Meaning
Feature What was measured, such as a circle or plane
Nominal The target value on the drawing
+Tol How far above nominal is allowed
-Tol How far below nominal is allowed (often printed as a negative)
Measured The value the machine found
Deviation Measured minus nominal
Out of tolerance The amount beyond the nearest limit, or zero
Detail B · A worked line

Example

Nominal 70.00, +0.03, -0.00, measured 70.02. Deviation = 70.02 - 70.00 = +0.02. The limits are 70.00 to 70.03, so it is in tolerance, with 0.01 left. A measured 70.04 would show deviation +0.04 and 0.01 out of tolerance.

Common mistakes

  • Reading deviation without the tolerance, so a small deviation seems fine on a tight tolerance.
  • Missing that a position result may already include a bonus tolerance.
  • Different report layouts: confirm each column's sign convention.

A second worked line

Nominal 12.50, tolerance plus 0.10 and minus 0.10. Measured 12.37. Deviation = 12.37 - 12.50 = -0.13. The limits are 12.40 to 12.60, so the part is 0.03 below the lower limit and is out of tolerance by 0.03. A report may show this as -0.03 in an out-of-tolerance column, or as a flag. Check which convention yours uses before you read a column.

Position and form results

For geometric tolerances the report usually shows the calculated result against the tolerance, such as a position of 0.21 against a limit of 0.30, rather than a nominal and deviation. The result may include a bonus tolerance already, so read the allowed value as well as the measured one. A position result is a diameter, which is why it can be larger than the coordinate deviations.

Reading the header

The header lists the part number, the programme, the date, the operator, the temperature where the machine records it and the alignment used. The alignment tells you which datums the machine built, so if it differs from the drawing, the results mean something different from what the drawing asks.

Checking a report before you trust it

  1. Part and revision match your drawing.
  2. Every characteristic on your ballooned drawing has a line.
  3. Spot-check three lines by hand.
  4. Out-of-tolerance flags agree with your own arithmetic.

Worked example from the sample part

Suppose the sample's seven characteristics had been measured on a coordinate measuring machine. The report would list them as the table below: nominal, tolerance, measured, deviation and verdict. For row 4, nominal 70.0, plus 0.03, minus 0, measured 70.02, the deviation is plus 0.02 and the remaining margin to the upper limit is 0.01. For row 3, nominal 110.0 plus or minus 0.1, measured 110.04, the deviation is plus 0.04 and the margin is 0.06.

Report rows for the sample drawing
No.RequirementMinMaxResultVerdict
120.0 ±0.219.820.220.08IN TOL
270.0 ±0.369.770.369.91IN TOL
3⌀110.0 ±0.1109.9110.1110.04IN TOL
4⌀70.0 +0.03/070.070.0370.02IN TOL
5⌀30.00 +0.02/030.0030.0230.01IN TOL
64X ⌀9.0 ±0.1 THRU8.99.19.05IN TOL
7⌀90.0 ±0.1 B.C.89.990.190.03IN TOL

Table: rows produced by the tool for the sample drawing. The measured results are made-up demo values.

The sample's measured values are demonstration values, not a real machine's output: a real report would also print the machine's own feature names, such as Circle1 or Plane2, which you map back to balloon numbers.

Mapping machine features to balloons

The usual weak point is the link between a machine feature and a drawing characteristic. A line called Circle3 means nothing to a reviewer unless the report also gives the balloon number. Keep a mapping table, or have the programme label each feature with its balloon number from the start.

Sign conventions

Deviation is measured minus nominal, so a positive deviation means the feature is bigger or further out than nominal. For a hole, bigger is positive. Some machines print deviation relative to the nearest limit instead, or print out-of-tolerance as a separate column. Read the legend on the report before comparing it with your own arithmetic.

When the CMM and the drawing disagree

If a CMM report calls a feature out of tolerance and a hand measurement calls it in, check the alignment and the datums first. The machine builds the datums from probed points, and if its alignment differs from the drawing's datum order the results mean different things. Then check temperature and the probe qualification.

Mistakes people make

  • Reading the deviation column without the tolerance.
  • Missing that a position result may already include a bonus.
  • Trusting a green pass flag without reading the alignment.
  • Copying results to a report without the balloon mapping.
Is a result exactly on the limit in tolerance?
Yes. See reading tolerances.
What does deviation mean on a CMM report?
Deviation is the measured value minus the nominal. A positive number means the feature measured larger or further out than nominal. Compare it with the tolerance, not on its own: a small deviation can still be out of tolerance when the tolerance is tight.
What does out of tolerance mean on a CMM report?
It is the amount by which the measurement lies beyond the nearest limit, and zero when it is inside. Some machines print it as a column and others as a flag. Check the report's legend.
What is nominal on a CMM report?
The target value from the drawing, which the tolerance is applied to. For a hole it is the dimension printed, for a position it is the basic location from the datums.
How do I check a CMM report?
Confirm the part and revision, check the alignment matches the drawing's datums, spot-check three lines by hand and make sure every ballooned characteristic has a line.

Open a drawing — free

Related

Do not scale drawingThird-angle projectionSheet 1 of 1balloonmydrawing.com
Built and supported by Paul: [email protected]. AS9102 is a standard of SAE International; this site is not affiliated with or endorsed by SAE. Nothing here reproduces the standard. Explanations are our own and are not legal or compliance advice.Privacy · Terms · Refunds